IKO Flashing Replacement Nationwide

IKO Flashing Replacement: The Pasadena Owner’s Guide

IKO flashing replacement in Pasadena typically runs between $350 and $850 installed, depending on how many linear feet are failing and whether we’re dealing with step flashing, pipe boot flashing, or valley flashing. We stock IKO-compatible flashing on our trucks and can usually complete the swap the same day we diagnose it. Most Pasadena homeowners discover the problem the hard way: a water stain on the ceiling after a winter rain, or granules collecting in the gutter below a wall intersection that should have been shedding water cleanly.

Call (626) 657-5397

Flashing is the metal transition piece between your IKO shingles and anything that interrupts the roof plane: chimneys, skylights, vent pipes, walls, valleys. When it fails, water gets behind the shingles and finds its way to the wood deck. We’ve pulled apart flashing jobs in Pasadena where the metal looked fine from the ground but had separated at the seam, or where the original installers had nailed through the flashing face instead of the flange, leaving a rust-widened hole for water to travel through.

Which IKO Models This Applies To

IKO flashing replacement applies across their entire residential shingle lineup, but the compatibility detail that matters is metal gauge and profile, not the shingle color or series. Whether your Pasadena roof is wearing Cambridge, Dynasty, Nordic, or Marathon, the flashing interface is the same: your roofer needs step flashing in 4×4 and 4×6 profiles matching the slope and wall height, galvanized or aluminum depending on exposure. We’ve also handled IKO’s Royal Estate and Armourshake, where the thicker dimensional profile means the flashing needs a wider step rise to keep water from backing up under the shingle edge.

If you still have the original roof paperwork, check for the IKO product label and any flashing specification noted. No paperwork? We’ll match by measuring the existing flashing during the inspection walk. For most Pasadena homes built before 2000, the original flashing was 26-gauge galvanized; we typically install 26-gauge or heavier galvanized or aluminum replacement, not thinner. IKO doesn’t manufacture proprietary flashing; they approve standard residential flashing profiles, so a quality aftermarket equivalent is functionally identical to whatever the builder installed. The key difference is the installer’s care, not the brand stamped on the metal.

Birchbark Roofing Pasadena is an independent service provider, not affiliated with IKO. We work with IKO-compatible flashing every week and keep common profiles stocked on our service trucks, alongside materials from GAF, Owens Corning, and CertainTeed.

Signs Your IKO Flashing Replacement Is Failing

• Ceiling stains below a wall or chimney line. This is the most common call we get from Pasadena homeowners after a good rain. Water travels down the flashing seam and into the roof deck, then shows up as a brown ring on the ceiling. The stain is usually a few feet away from the actual leak point.
• Visible rust or pitting on the flashing face. Galvanized flashing eventually sacrifices its zinc coating, especially on Pasadena roofs where morning marine layer moisture lingers and afternoon sun bakes the metal. Rust means the metal is thinning and holes are forming.
• Lifted shingle edges near walls or dormers. As flashing expands and contracts through hot Pasadena summers and cool winter nights, poorly fastened or under-sized pieces can push the shingle edge upward. That little upturned lip is an open invitation for wind-driven rain.
• Granules in the gutter directly below a wall intersection. Granule loss concentrated at a flashing line means water is streaming sideways across the shingle surface, scrubbing granules loose as it goes. The shingle above the flashing is often the leak, but the flashing height or fold is usually the root cause.
• Daylight visible at the roof wall seam from the attic. Get into the attic on a bright Pasadena afternoon and look along the wall where it meets the roofline. If you can see light through gaps at the flashing line, water has already been getting in during any storm with enough wind behind it.

Replacement Cost & What’s Included

Most IKO flashing replacement jobs in Pasadena range from $350 for a single vent pipe boot or a short section of step flashing up to $850 for a full chimney saddle and apron replacement. If the failed flashing has done more damage, like rotted deck boards or a soaked underlayment section, the scope and price adjust accordingly and we’ll show you photos of what we found before we ask you to agree to anything.

Every flashing replacement we write in Pasadena includes the new flashing, the sealant appropriate for the material, any needed shingle lift and re-fastening around the work area, and a written price in dollars before the first tool comes off the truck. You’ll see the line items, not a handshake number. The work is covered under our 365-Day Done Right Promise: if it isn’t right, we make it right. And because we’re part of the Cedarwell family of roofing companies, the crew arrives background-checked and uniformed, with shoe covers at the door and drop cloths through the hallway.

DIY or Call Us?

You can safely check the symptoms from the ground or the attic. A good look at the flashing with binoculars on a dry Pasadena afternoon, or a peek at the wall seam from inside the attic, costs nothing and helps you describe what’s going on when you call. What you shouldn’t do is get on the roof and start prying up shingles, especially on a two-story Pasadena house with a steeper pitch. A finished roof surface is a working height plus a fall risk, and separating a shingle line without the right lift technique leaves adhesive damage that makes the next repair more expensive.

Flashing work also needs the right sealant for the material match, and getting the overlap wrong means the repair fails quietly until the next big rain reveals it. If the dog needs to stay inside while we work, we’ll coordinate the door schedule with you. Call (626) 657-5397 and we’ll have someone take a careful look.

FAQs